● General Description:
The SFP 10G Bidi is a small form factor pluggable module for 10 Gigabit Ethernet. This transceiver communicates over 1 single strand of single fiber. The SFP 10G Bidi comes in a U and D version the D sends out with 1330nm and receives with 1270nm. The U version sends out with 1270nm and receives with 1330nm. For communication you need the D and U on each side of the line. Because the attenuation at 1310nm is too high the 80km version works on 1570/1490 transmit and receive.
● Product features:
► Operating data rate up to 10.3Gbps;
► 1270 or 1330nm BOSA for 20/40/60km;
► 1490 or 1570nm BOSA for 80km;
► 20km or 40km or 60km or 80km over a single strand of single fiber;
► Single 3.3V power supply and TTL logic interface simplex LC connector interface;
► Hot pluggable;
► Standard as commercial operating case temperature: from 0℃ to +70℃;
► Industrial version available: from -40℃ to +85℃, this is indicated with an extra "I" in the partname;
► Compliant with MSA SFP specification;
► Digital diagnostic monitor interface (also called DOM or DDM);
► Compatible with SFF-8472.
● Description:
Form Factor | SFP+ / SFP10G |
Compatibility | Cisco compatible |
Distance | 20km |
Wavelength | TX 1270/RX 1330 |
Speed | 10G |
Connector | LC |
Individually Tested | Yes |
Power Budget Verification | Yes |
Lifetime Warranty | Yes |
Type | BiDi |
Power Budget | 10dB |
Fiber Type | Single-mode |
● Optical characteristics transceiver:
Parameters | Symbols | Min | Typ | Max | Unit |
20km | |||||
Centre Wavelength BXD | λC | 1320 | 1330 | 1340 | nm |
Centre Wavelength BXU | λC | 1260 | 1270 | 1280 | nm |
Spectral Width (RMS) | σ |
|
| 1 | nm |
Average Output Power | P0ut | -3 |
| +2 | dBm |
Extinction Ratio | EX | 3.5 | 6 |
| dB |
40km | |||||
Centre Wavelength BXD | λC | 1320 | 1330 | 1340 | nm |
Centre Wavelength BXU | λC | 1260 | 1270 | 1280 | nm |
Spectral Width (RMS) | σ |
|
| 1 | nm |
Average Output Power | P0ut | 0 |
| 5 | dBm |
Extinction Ratio | EX | 3.5 | 6 |
| dB |
60km | |||||
Centre Wavelength BXD | λC | 1320 | 1330 | 1340 | nm |
Centre Wavelength BXU | λC | 1260 | 1270 | 1280 | nm |
Spectral Width (RMS) | σ |
|
| 1 | nm |
Average Output Power | P0ut | 1 |
| 5 | dBm |
Extinction Ratio | EX | 3.5 | 6 |
| dB |
80km | |||||
Centre Wavelength BXD | λC | 1530 | 1570 | 1580 | nm |
Centre Wavelength BXU | λC | 1480 | 1490 | 1500 | nm |
Spectral Width (RMS) | σ |
|
| 0.3 | nm |
Average Output Power | P0ut | 1 |
| 5 | dBm |
Extinction Ratio | EX | 8.2 |
|
| dB |
Output Optical Eye | Compliant with FC_FI_4 REV 7.0 | ||||
Data Input Swing Differential | VIN | 180 |
| 700 | mV |
Input Differential Impedance | ZIN | 85 | 100 | 115 | Ω |
TX Fault Output High | TxFh | 2.4 |
| Vcc | V |
TX Fault Output Low | TxFl | -0.3 |
| 0.8 | V |
TX Disable Output High | TxDh | 2 |
| Vcc+0.3 | V |
TX Disable Output Low | TxDl | -0.3 |
| 0.8 | V |
● Optical characteristics receiver:
Parameters | Symbols | Min | Typ | Max | Unit |
20km | |||||
Centre Wavelength BXD | λC | 1260 | 1270 | 1280 | nm |
Centre Wavelength BXU | λC | 1320 | 1330 | 1340 | nm |
Reveiver Sensitivity | Sen | -14.5 |
|
| dBm |
Maximum input | Pmax | 0 |
|
| dBm |
LOS De-Assert | LOSd |
|
| -14 | dBm |
LOS Assert | LOSa | -25 |
|
| dBm |
LOS Hysteresis | LOSh | 0.5 |
| 4 | dBm |
40km | |||||
Centre Wavelength BXD | λC | 1260 | 1270 | 1280 | nm |
Centre Wavelength BXU | λC | 1320 | 1330 | 1340 | nm |
Reveiver Sensitivity | Sen | -16 |
|
| dBm |
Maximum input | Pmax | 0 |
|
| dBm |
LOS De-Assert | LOSd |
|
| -17 | dBm |
LOS Assert | LOSa | -27 |
|
| dBm |
LOS Hysteresis | LOSh | 0.5 |
| 4 | dBm |
60km | |||||
Centre Wavelength BXD | λC | 1260 | 1270 | 1280 | nm |
Centre Wavelength BXU | λC | 1320 | 1330 | 1340 | nm |
Reveiver Sensitivity | Sen | -22 |
|
| dBm |
Maximum input | Pmax | -7 |
|
| dBm |
LOS De-Assert | LOSd |
|
| -23 | dBm |
LOS Assert | LOSa | -33 |
|
| dBm |
LOS Hysteresis | LOSh | 0.5 |
| 4 | dBm |
80km | |||||
Centre Wavelength BXD | λC | 1480 | 1490 | 1500 | nm |
Centre Wavelength BXU | λC | 1530 | 1570 | 1580 | nm |
Reveiver Sensitivity | Sen | -22 |
| -7 | dBm |
Maximum input | Pmax | -7 |
|
| dBm |
LOS De-Assert | LOSd |
|
| -24 | dBm |
LOS Assert | LOSa | -34 |
|
| dBm |
LOS Hysteresis | LOSh | 0.5 |
|
| dBm |
Dispersion penalty |
|
|
| 3.0 | dBm |
● Electrical characteristics:
Parameters | Symbols | Min | Typ | Max | Unit | Remarks |
Supply Voltage | Vcc | 3.14 | 3.3 | 3.46 | V |
|
Supply Current 20km | Icc |
| 270 | 350 | mA |
|
Supply Current 40km |
|
| 300 | 450 | mA |
|
Supply Current 60km |
|
| 300 | 450 | mA |
|
Supply Current 80km |
|
|
| 500 | mA |
|
| ||||||
Supply Voltage | Vcc | 3.14 | 3.3 | 3.46 | V |
|
Supply Current | Icc |
|
| 300 | mA |
|
Reference Differential Input | Zd |
| 100 |
| mA |
|
Input AC Common Mode Input |
| 0 | 25 |
| mA |
|
Differential Input Voltage Swing | VID | 150 |
| 900 | mA |
|
Total Jitter |
|
|
|
|
|
|
Data Dependant Jitter |
|
|
|
|
|
|
Uncorrelated Jitter |
|
|
|
|
|
|
Eye Mask | See SFP+ MSA | X1 |
|
|
| UI |
Eye Mask | See SFP+ MSA | X2 |
|
| 0.35 | UI |
● DOM parameters:
Parameters | Min | Max | Unit |
Transponder temperature monitor accuracy | -5 | +5 | ℃ |
Laser bias current monitor accuracy | -10 | +10 | % |
Transmit power monitor accuracy | -2 | +2 | dB |
Receive power monitor accuracy | -2 | +2 | dB |
● Absolute conditions:
Parameters | Symbols | Min | Max | Unit |
Storage temperature | Ts | -40 | 85 | ℃ |
Power supply voltage | Vcc | -0.5 | 4 | V |
Signal input voltage |
| -0.3 | Vcc+0.3 | V |
Operating temp COM version |
| 0℃ | 70℃ |
|
Operating temp IND version |
| -40℃ | +85℃ |
|